Logo
Get Estimate

Leak Detection Fort Worth TX that finds hidden leaks fast

Thermal imaging and moisture mapping for slab, pipe, and roof leaks


Leak Detection Fort Worth TX starts with a moisture meter and a thermal imaging camera, not a sledgehammer. We trace slab leaks, pinhole pipe leaks, and roof intrusion across Tarrant County before they rot framing and feed black mold. If your water bill jumped or a floor feels warm, call us. We find the source, document it, and hand you a repair plan the same day.

Forensic investigators in white suits and masks examining a crime scene outside a residential area.
Licensed Licensed & Bonded
Fully Insured Insured & Bonded
24/7 Emergency Same-Day Response
Warranty Backed Workmanship Guaranteed in Fort Worth

What Is Included in Every Leak Detection Visit

A standard diagnostic covers the full interior and accessible exterior of the home. If the leak turns out to be in a place we cannot reach without opening a wall, we tell you that in the report and hand the exact location to your plumber or roofer.

Full Moisture Mapping

Twelve to twenty moisture meter readings per floor, logged on a sketch of your layout with a Protimeter meter and hygrometer. You see exactly where readings are elevated and how far they spread from the source.

Thermal Imaging Scan

A FLIR thermal imaging camera sweep of every wall, floor, and ceiling plane we can access. Wet materials show a temperature delta the camera catches, which is how we find leaks behind finished surfaces without cutting anything open.

Acoustic Leak Confirmation

For pressurized supply lines, we listen for the sound of water escaping under pressure and isolate the line to confirm the thermal hit. Two methods agreeing on the same spot is how we get location accuracy inside 12 inches.

Written Diagnostic Report

A printed and emailed report with thermal images, moisture percentages, the marked leak location, and photos of anything we accessed. This is the document your insurance adjuster, plumber, and remediation contractor will all ask for.

Repair Referral Guidance

We tell you whether the fix belongs to a plumber, a roofer, a foundation contractor, or an HVAC tech, and we hand over the documentation they need. You are not left guessing who to call next.

Leak Detection Fort Worth TX: What We Actually Do


Leak Detection Fort Worth TX is a non-invasive diagnostic service that pinpoints where water is escaping or entering a building before any drywall or slab gets opened. We start with a moisture meter and a Protimeter hygrometer to map elevated readings room by room, then confirm the source with a FLIR thermal imaging camera and, when needed, a boroscope pushed through a wall cavity. You get a marked-up moisture map, photos, and a written summary of where the water is coming from and how far it has traveled.

Fort Worth homes sit on expansive clay soils that shift hard between our dry summers and wet springs, and that movement cracks cast-iron drain lines and copper supply lines under slabs. Add 100-degree July attic temperatures and the condensation that follows, and you get the three calls we run most: a water bill that doubled, a warm spot on a tile floor, or a musty smell in a hallway closet. If you have been searching water leak detection near me Fort Worth at 11 p.m. with a towel on the floor, we answer.

What to Expect During Your Leak Detection Visit

Most residential leak detection jobs in Fort Worth run two to four hours. Here is the sequence, start to finish, so you know exactly what happens in your home.

01

Schedule

Call or book online — a real human picks up and confirms a 2-hour arrival window.

02

Diagnose

Licensed tech inspects on-site, then walks you through the cause and your options.

03

Fix

The job is completed to code and done right the first time — no shortcuts, no surprises.

04

Guarantee

Every job backed by a written workmanship warranty — and we stand behind it.

Tools and Methods We Use on Every Job

Tools & Equipment

FLIR Thermal Imaging Camera

Reads temperature differences caused by wet materials behind walls, under slabs, and above ceilings. It is the fastest way to see a leak path without opening anything up.

Protimeter Moisture Meter

Takes pin and pinless readings on drywall, framing, and flooring. We log percentages at every test point so we can chart how far water has traveled from the source.

Hygrometer

Measures relative humidity and dew point so we can tell a real leak from a condensation problem. This is what keeps us from chasing the wrong fix.

Boroscope

A slim camera we push through a small access hole to see inside wall cavities, under cabinets, and behind tub surrounds. It confirms what thermal imaging suggests.

Acoustic Listening Equipment

Picks up the sound of pressurized water escaping a supply line. We use it to confirm slab and under-slab leaks that thermal imaging flags.

Air-O-Cell Spore Trap Cassettes

Collect airborne spores when a leak has been running long enough to affect indoor air. Samples go to EMSL Analytical for lab analysis.

ERMI Dust Cloths

Collected from floors and surfaces and analyzed by Mycometrics to produce a single mold-load score for the whole house.

Methods & Standards

ANSI/IICRC S520 Moisture Assessment

The industry standard for evaluating water-damaged buildings. It governs how we classify the water, how we measure moisture, and how we document findings so the report holds up with adjusters and remediators.

Two-Method Confirmation

We never call a leak on one tool alone. Thermal imaging plus moisture meter, or acoustic listening plus pressure isolation, has to agree on the same spot before we mark it. That is how we get location accuracy inside 12 inches.

Pressure Isolation Testing

For slab leaks, we isolate sections of the supply system and watch the meter to confirm which line is losing water. It narrows a whole-house search down to one run of pipe.

Moisture Gradient Mapping

We take readings at increasing distances from the suspected source and chart the gradient. Water always reads highest at the source, so the gradient tells us the direction and extent of the spread.

When to Call for Leak Detection

01

You are buying a home in Ryan Place or Mistletoe Heights and the inspection report mentions past water staining.

What we do: We run leak detection alongside moisture mapping and air sampling so you know whether the stain is old and dry or an active leak still feeding mold behind the wall.

→ You get a written report you can use to negotiate repairs or walk away with confidence.

02

A pipe burst over the weekend and you had it repaired, but the drywall still feels cool to the touch.

What we do: We map moisture across the affected rooms, confirm whether the wall cavity has dried, and check for mold growth with tape lift and swab sampling if it has been wet more than 48 hours.

→ You know whether to dry and paint, or whether remediation is needed before you close the wall back up.

03

Your water heater is 12 years old and the pan under it has a ring of rust.

What we do: We inspect the pan, the supply lines, and the T&P discharge, then take moisture readings on the surrounding framing and flooring to catch a slow drip before it spreads.

→ You replace the heater on your schedule instead of cleaning up a flood on a holiday weekend.

04

You manage a commercial building in Downtown Fort Worth and a tenant reports a damp spot on the ceiling tile.

What we do: We trace the leak through the plenum with thermal imaging, check the HVAC condensate line and roof penetrations, and document the moisture spread for your maintenance records.

→ The right trade gets called, the tile gets replaced once, and the tenant stops filing complaints.

How Leak Detection Works in Fort Worth

Fort Worth sits on expansive clay that swells when it rains and shrinks hard in summer, and that cycle cracks cast-iron drain lines and copper supply lines under slabs across Ridglea, Wedgwood, and Tanglewood. Our wet springs push water against foundations and into crawl spaces, while July and August attic temperatures above 130 degrees drive condensation that mimics a leak. We adjust our approach by neighborhood: pier-and-beam homes in Fairmount and Ryan Place get crawl space moisture mapping alongside the interior scan, while slab-on-grade builds get pressure isolation and acoustic confirmation. Tarrant County code and ANSI/IICRC S520 both shape how we document findings, and we work to that standard on every job. If you need water leak detection near me Fort Worth TX 24/7 for an active leak, we take after-hours calls and dispatch with a full kit.

Neighborhoods We Serve

  • Ridglea

    Mid-century slab-on-grade homes with original copper supply lines. Pinhole leaks in these lines are our most common slab call in the area.

  • Fairmount

    Historic pier-and-beam properties where crawl space humidity and slow drain leaks under bathrooms are the recurring issues.

  • Tanglewood

    Larger lots with mature trees whose roots invade sewer laterals. We confirm root intrusion with a boroscope before recommending a fix.

  • Wedgwood

    1990s two-story builds where second-floor bathroom supply lines drip into first-floor ceilings. Thermal imaging catches these fast.

  • Eastchase

    Newer construction where we most often find HVAC condensate line failures and improperly sealed roof penetrations.

Local Conditions We Plan For

  • Expansive clay soil movement

    Shifting clay cracks under-slab plumbing and opens gaps at foundation penetrations. We see a spike in slab leak calls after both drought and heavy rain cycles.

  • Summer attic temperatures above 130 degrees

    Extreme heat drives condensation on cool ductwork and plumbing, which can look exactly like a leak. We separate the two with hygrometer readings before recommending repairs.

  • Spring hail and heavy rain events

    Roof penetrations and flashing fail under hail, and the resulting leaks often show up weeks later as attic mold. We trace the water path back to the failed point.

  • High indoor humidity in tight newer homes

    Modern construction traps moisture, so condensation forms on cool surfaces and feeds mold without any leak. We measure dew point to tell the difference.

Slab Leak Caught Before Foundation Damage

Before

A Ridglea homeowner noticed a warm spot on the hallway tile and a water bill up $90. Two previous plumbers quoted exploratory demolition of the entire hallway floor to find the source, with no guarantee of success.

After

Thermal imaging and acoustic listening located the leak within 12 inches in under two hours. The plumber opened one 18-inch section of tile, repaired the line, and the homeowner avoided roughly $3,800 in unnecessary demolition and flooring replacement.

Maintenance: We recommended a moisture check every six months for the first year and a slab moisture barrier to reduce future clay movement under the foundation.

Before

A Fairmount family had a musty smell in a back bedroom for three months. Two companies told them it was old-house humidity. Moisture readings in the closet wall hit 24 percent, well above the 16 percent threshold for drywall.

After

Thermal imaging found a slow supply line leak inside the wall cavity. We documented the moisture spread, the plumber repaired the line, and air sampling confirmed spore counts were still within normal range, so no remediation was needed.

Maintenance: We set them up with a quarterly humidity check and a small dehumidifier for the crawl space to keep the pier-and-beam area dry.

Before

After a spring hailstorm, a Wedgwood homeowner found a brown ring on the ceiling. The roofer could not find the entry point, and the insurance adjuster initially denied the water damage claim for lack of documentation.

After

We traced the water path from the ceiling stain back to a failed pipe boot flashing, documented the attic decking moisture at 22 percent with thermal images and photos, and the claim was approved for $6,400 in repairs.

Maintenance: We recommended an attic inspection after every hail event and a moisture check each spring before storm season starts.
Why Fort Worth Homeowners Call Us First

Why Fort Worth Homeowners Call Us First

Finding the leak is the cheap part. Finding it before it destroys your foundation, your flooring, and your air quality is the whole point. Here is what a proper leak detection visit buys you.

  • Stop Mold Before It Starts

    Mold colonizes wet drywall in 24 to 48 hours. When we locate a slab leak or supply-line drip on day one, you skip the tear-out, the antimicrobial coatings, and the HEPA-filtered containment. One Fort Worth customer caught a pinhole leak under a bathroom vanity within 36 hours and saved roughly $4,200 in remediation.

  • Cut the Water Bill Fast

    A pencil-thin supply leak can waste 8,000 to 10,000 gallons a month. At Fort Worth rates that is $60 to $120 added to every bill. We isolate the leak, tag the line, and give your plumber an exact location, so the repair happens once, in the right spot, without exploratory demolition.

  • Protect the Foundation

    Water under a slab softens the clay and the slab moves. We map moisture gradients across the floor so you know whether the leak is under the slab, in a wall, or coming in from the roof. Catching it early keeps you out of a $15,000 to $40,000 foundation repair conversation.

  • Documentation for Insurance

    Adjusters want proof, not a hunch. Our reports include thermal images, moisture readings in percent, and a floor plan marked with the leak location. That packet is what turns a denied water damage claim into an approved one, and it is the same documentation we use for post-remediation clearance testing.

Questions Fort Worth Homeowners Ask Us

Real answers to the questions we hear most often from local homeowners and property managers.

How much does Leak Detection cost in Fort Worth TX?
Most residential leak detection visits in Fort Worth run $250 to $550 in 2026, depending on square footage and how many methods we need. Slab leaks that require pressure isolation sit at the top of that range. You get the price before we start, and the diagnostic fee is credited if you book follow-up moisture mapping or clearance testing with us.
How do I know if I have a water leak in Fort Worth?
Four signs show up over and over: a water bill that jumped 20 percent or more with no change in use, a warm or damp spot on a hard floor, a musty smell in a closet or hallway, and a water meter that keeps spinning with every fixture off. Any two of those together justify a professional leak detection Fort Worth visit.
Can leak detection find hidden pipe leaks in Fort Worth TX?
Yes. Hidden supply and drain leaks behind walls and under slabs are exactly what thermal imaging and acoustic listening are built for. We confirm each hit with two independent methods, so you get a location accurate to roughly 12 inches rather than a general area. Your plumber then opens one small access point instead of three.
Does Leak Detection include thermal imaging in Fort Worth?
Yes, every diagnostic visit includes a FLIR thermal imaging scan at no extra charge. We pair it with moisture meter readings and, when the leak is pressurized, acoustic confirmation. Thermal alone can misread a duct or a sun-warmed wall, which is why we never rely on a single tool to call a leak.

Services That Pair With Leak Detection

Mold Inspection

Once we locate the leak, a full mold inspection tells you whether the wet materials have already colonized. We check attics, crawl spaces, and wall cavities in the same visit so you get one report covering both the water source and any growth it caused.

View Mold Inspection

Mold Testing

If you can smell something musty but cannot see it, mold testing confirms what is airborne. We collect tape lift and swab samples from suspect surfaces and send them to EMSL Analytical, then match the results to the leak location we mapped.

View Mold Testing

Air Quality Testing

A hidden leak that has been running for weeks feeds spores into your air. We run spore trap cassettes through an Air-O-Cell sampler and compare indoor counts to an outdoor baseline, which tells you whether the leak has affected the air your family breathes.

View Air Quality Testing

Moisture Mapping and Detection

Moisture mapping is the backbone of leak detection. We log readings at 12 to 20 points per floor with a Protimeter meter and hygrometer, then chart how far water has traveled from the source. That map drives every repair and drying decision that follows.

View Moisture Mapping and Detection

Thermal Imaging Inspection

A FLIR camera reveals temperature differences that wet materials create behind walls and under slabs. We use it on every leak call, and it is especially effective on slab leaks and roof intrusion where the water path is not visible from the surface.

View Thermal Imaging Inspection

Mold Remediation Protocol

When a leak has already fed black mold, we write the remediation protocol: containment, HEPA filtration, antimicrobial coatings, and clearance criteria. It follows ANSI/IICRC S520 and gives your remediation contractor a clear scope to bid against.

View Mold Remediation Protocol

Book Leak Detection Fort Worth TX Before the Damage Spreads

A leak that has been running a week has already cost you more than the diagnostic. Call Fort Worth Mold Testing and we will find the source, document it, and tell you exactly what to fix. Same-day slots are held for active leaks, and you get the price before we start.

Call Now Schedule Leak Detection

Contact Fort Worth Mold Testing

Call (866) 896-8166 or email info@fortworthmoldtesting.com and we will get you on the schedule. We answer calls Monday through Friday from 8am to 6pm and run emergency response for water damage and post-storm inspections. Most standard inspections are booked within a day or two.

Or call us right now at +18668968166 — we answer.

Fort Worth Mold Testing


  • Phone

    +18668968166
  • Address

    Fort Worth, Texas

  • Hours

    Mon–Fri: 7AM – 7PM
    Sat: 8AM – 4PM
    Sun: Emergency Only
    24/7 Emergency Available

Call +18668968166 Get Quote
Call Quote