Logo
Get Estimate

Thermal Imaging Inspection Fort Worth TX finds hidden moisture fast

See behind walls before mold spreads


A Thermal Imaging Inspection Fort Worth TX shows you exactly where water is hiding behind drywall, under flooring, and inside ceilings, without cutting a single hole. We use FLIR thermal cameras paired with moisture meters to confirm what the camera finds. If you have smelled something musty, seen a new stain, or had a recent roof or slab leak, this is the fastest way to find the source before mold takes hold.

Close-up of a car engine inspection using a diagnostic tool in a garage setting, showcasing automotive maintenance and repair.
Licensed Licensed & Bonded
Fully Insured Insured & Bonded
24/7 Emergency Same-Day Response
Warranty Backed Workmanship Guaranteed in Fort Worth

What is included in a thermal imaging inspection

Every Thermal Imaging Inspection Fort Worth TX we perform includes the same core deliverables. If you need additional testing like air sampling or ERMI, we can add it to the same visit so you do not pay for a second trip.

Full thermal scan

We scan every accessible wall, ceiling, and floor with a FLIR thermal imaging camera. This includes the attic, crawl space, bathrooms, kitchen, laundry area, and HVAC closet. The scan takes 60 to 90 minutes for a typical Fort Worth home.

Moisture meter confirmation

Every thermal anomaly gets confirmed with a Protimeter moisture meter and a hygrometer. We do not report a leak based on a camera image alone. If the meter reads elevated moisture, we mark the exact boundaries of the wet zone.

Written report with photos

You get a same-day written report with timestamped thermal images, moisture percentages, a floor-plan sketch of affected areas, and a plain-language summary. The report is formatted for insurance adjusters and remediation contractors.

Humidity and ventilation check

We measure indoor humidity with a hygrometer and check bathroom fans, kitchen exhaust, and attic ventilation. High humidity and poor airflow are two of the most common reasons mold comes back after remediation, so we document them in the report.

Next-step recommendations

We walk you through the findings and lay out your options. If mold testing is needed, we explain which method makes sense: air sampling, tape lift, swab, or ERMI. If remediation is needed, we outline the scope and connect you with TDLR-licensed contractors.

What Thermal Imaging Inspection Fort Worth TX actually does


A Thermal Imaging Inspection Fort Worth TX is a non-invasive diagnostic that uses an infrared camera to map temperature differences across walls, ceilings, and floors. Wet building materials hold heat differently than dry ones, so a trained eye can spot a hidden leak, a slow slab leak, or a saturated patch of insulation in seconds. We pair the camera with a Protimeter moisture meter and a hygrometer to confirm every reading, then document everything with photos and a written report you can hand to your insurance company or a remediation crew.

Fort Worth homes deal with a specific set of moisture problems. Summer humidity sits above 60% for weeks, spring storms push water through aging roof flashings, and clay soil shifts enough to crack slab plumbing. That combination creates hidden leaks that never show a visible stain until mold has already colonized the drywall. If you have been searching for infrared inspection near me Fort Worth TX 24/7 because of a mystery smell or a spike in your water bill, this scan is where we start.

How our thermal imaging process works

Every Thermal Imaging Inspection Fort Worth TX follows the same five steps. No surprises, no vague findings, and no pressure to book anything else.

01

Schedule

Call or book online — a real human picks up and confirms a 2-hour arrival window.

02

Diagnose

Licensed tech inspects on-site, then walks you through the cause and your options.

03

Fix

The job is completed to code and done right the first time — no shortcuts, no surprises.

04

Guarantee

Every job backed by a written workmanship warranty — and we stand behind it.

Tools and methods we use

Tools & Equipment

FLIR thermal imaging camera

The primary tool for every scan. It detects temperature differences across surfaces, revealing hidden moisture, air leaks, and missing insulation. We use it on walls, ceilings, floors, and in the attic and crawl space.

Protimeter moisture meter

Confirms every thermal anomaly with a direct moisture reading. We use both pin and pinless modes depending on the surface. This is what separates a real finding from a false alarm.

Hygrometer

Measures relative humidity in each room and in the attic and crawl space. High indoor humidity is a leading cause of condensation and mold growth in Fort Worth homes.

Boroscope

A flexible camera we insert into wall cavities, ductwork, and tight spaces to see what the thermal camera cannot. We use it to confirm mold growth, check insulation condition, and inspect HVAC components.

Zefon Air-O-Cell cassettes

Spore trap cassettes used with an air sampling pump to capture airborne mold spores. Samples are sent to EMSL Analytical or LabCorp for species identification and spore count.

ERMI dust cloths

A single dust sample that measures 36 mold species in the home. Analyzed by Mycometrics or EMSL Analytical. Useful when you want a broader picture of mold history beyond what a thermal scan shows.

Methods & Standards

ANSI/IICRC S520 moisture assessment

We follow the S520 standard for assessing moisture and mold conditions. This means documenting moisture content, defining the affected area, and establishing a clear scope of work. It is the same standard remediation contractors use, so our reports plug directly into their process.

Thermal-plus-meter confirmation

We never report a leak based on a thermal image alone. Every anomaly gets confirmed with a Protimeter moisture meter and, when relevant, a hygrometer reading. This two-step method eliminates false positives from reflective surfaces, sun-loaded walls, and ductwork.

Zone mapping

We mark the exact boundaries of every wet zone on a floor-plan sketch. This gives remediation crews a precise scope and helps insurance adjusters size the claim. It also gives you a baseline to compare against if you re-scan after repairs.

Air and surface sampling

When thermal imaging shows conditions that support mold growth, we add air sampling with Zefon Air-O-Cell cassettes, tape lift sampling, or swab sampling. Samples go to EMSL Analytical or LabCorp, and results come back in two to three business days.

When to book a thermal imaging inspection

01

You just bought a Fort Worth home and the inspection report mentioned past water damage.

What we do: We scan the areas flagged in the report, plus the attic, crawl space, and HVAC system, to confirm whether the moisture is still active. We document everything with thermal images and moisture readings so you know what you are dealing with.

→ You get a clear picture of whether the past water damage is a resolved issue or an active problem, and a written report you can use to negotiate repairs or plan remediation.

02

A pipe burst over the winter and you want to confirm the wall is dry before you close it up.

What we do: We scan the affected wall and the surrounding area with a thermal camera, then confirm with a moisture meter. If the wall cavity is still wet, we mark the exact boundaries so your contractor knows how far to open it up.

→ You avoid closing up a wall that still has moisture inside, which is the number one cause of mold growth after a plumbing repair.

03

You are selling your Fort Worth home and the buyer's inspector flagged a musty smell.

What we do: We run a thermal scan and moisture check to determine whether there is an active moisture problem. If mold testing is needed, we add air sampling or tape lift sampling in the same visit and get results back from the lab in two to three business days.

→ You get a documented answer that either clears the concern or gives you a clear scope of work to address before closing.

04

Your HVAC system has been running constantly and you notice condensation on the vents.

What we do: We inspect the air handler, drip pan, and ductwork with a boroscope, scan for condensation with a thermal camera, and measure indoor humidity with a hygrometer. If mold is present in the system, we sample the supply air with an Air-O-Cell cassette.

→ You find out whether the HVAC system is spreading mold spores through your home, and you get a remediation scope if it is.

How thermal imaging runs in Fort Worth

Fort Worth has a moisture profile that is different from most Texas cities. Summer humidity sits above 60% for weeks, spring storms push water through aging roof flashings, and the clay soil expands and contracts enough to crack slab plumbing. That combination means hidden leaks are common and often go unnoticed until mold has already taken hold. Our thermal imaging inspections are built around those conditions. We pay extra attention to slab edges in older neighborhoods like Fairmount and Ryan Place, roof decking in attic spaces, and HVAC closets where condensation collects. If you are searching for affordable infrared inspection Fort Worth TX after a storm, we can usually get a tech out the same day. We also work regularly with TDLR-licensed remediation contractors, so if the scan turns up mold, we can connect you with someone who can start work quickly.

Neighborhoods We Serve

  • Fairmount

    1920s bungalows with original plumbing and pier-and-beam foundations. Slab leaks are less common here, but crawl space moisture and failed moisture barriers are frequent findings.

  • Tanglewood

    Mid-century ranches with slab foundations and mature trees. Root intrusion into sewer lines and slow slab leaks are the two most common moisture sources we find.

  • Downtown Fort Worth

    High-rise condos and older commercial buildings with flat roofs and large HVAC systems. Condensation on ductwork and roof membrane failures are the top two issues.

  • Eastchase

    Newer construction with tight building envelopes. Poor attic ventilation and HVAC condensation are more common than plumbing leaks in these homes.

Local Conditions We Plan For

  • High summer humidity above 60%

    Elevated indoor humidity slows evaporation and keeps wall cavities damp longer after a leak. This gives mold a longer window to colonize, which is why we always measure humidity with a hygrometer during a scan.

  • Expansive clay soil

    Fort Worth's clay soil shifts with moisture changes, which stresses slab plumbing and can cause slow leaks under the foundation. Thermal imaging is one of the few ways to find these leaks without breaking up the slab.

  • Spring storm season

    Hail and wind-driven rain push water through roof flashings, vents, and window seals. We see a spike in thermal imaging calls every March through June for ceiling stains and attic moisture.

  • Aging housing stock

    Homes built before 1980 often have original supply lines, cast-iron drains, and undersized ventilation. These homes are more likely to have hidden leaks and chronic moisture problems that a thermal scan can reveal.

Slab leak found under bathroom tile

Before

A Fairmount homeowner noticed a musty smell in the hallway and a water bill that had crept up $40 a month. There was no visible stain and no obvious leak. Two plumbers had already told them there was nothing wrong.

After

Our thermal scan found a cold spot under the bathroom tile that traced back to a slow slab leak. We confirmed with a moisture meter and documented the wet zone. The plumber used our report to pinpoint the repair, and the homeowner avoided tearing up the entire bathroom floor.

Maintenance: We recommend re-scanning the area 30 days after the repair to confirm the slab has dried. If humidity stays above 55%, a dehumidifier will help prevent mold from returning.

Before

After a spring hailstorm, a Tanglewood homeowner saw a small stain on the ceiling but assumed it was cosmetic. Three weeks later, the stain had grown and the attic smelled musty. They called us before calling a roofer.

After

Thermal imaging showed the leak had soaked 30 square feet of attic insulation, far beyond the visible stain. We documented everything with thermal images and moisture readings. The roofer fixed the flashing, and the homeowner replaced the insulation before mold could take hold.

Maintenance: We recommend checking the attic after every major storm and keeping indoor humidity below 55%. A $20 hygrometer is enough to monitor it.

Before

A property manager had cleaned mold off the ceiling of a rental unit twice in one year. Each time it came back within a few months. The tenant complained of a musty smell, and the manager was losing rent from turnover.

After

Our thermal scan found condensation on the HVAC ductwork above the ceiling, which was dripping onto the drywall. We confirmed with a hygrometer and documented the issue. The HVAC contractor insulated the duct, and the mold has not returned in over a year.

Maintenance: We recommend an annual HVAC inspection and keeping the air filter changed every 60 to 90 days. Both reduce condensation and improve indoor air quality.

Hidden moisture problems we solve in Fort Worth

Most Fort Worth homeowners call us after they have already tried to find the problem themselves. Here are the four issues we solve most often with thermal imaging.

Problem

Musty smell with no visible source

A musty smell almost always means active mold growth somewhere you cannot see. By the time the smell is strong, the mold colony is usually well established and the affected area is larger than you would expect.

Our Fix

We scan every room with a thermal camera and confirm with a moisture meter. In most cases we find the source in under an hour: a slow supply-line drip, a failed shower pan, or condensation on cold ductwork. You get a clear answer and a documented report.

Problem

Water stain on ceiling or wall

A stain means water has already traveled through the building materials. The visible stain is usually only the edge of a much larger wet zone hiding behind the drywall or above the ceiling.

Our Fix

Thermal imaging shows the full extent of the moisture, not just the visible stain. We map the wet zone, measure moisture percentages, and document everything with photos. Your roofer or plumber gets a precise target instead of guessing where to cut.

Problem

High water bill with no obvious leak

A slab leak or a hidden supply-line leak can waste hundreds of gallons a week. Left alone, it undermines the foundation and creates ideal conditions for mold growth under the flooring.

Our Fix

We scan the slab edge, walls, and floors with a thermal camera to find the temperature signature of a hidden leak. Once we locate it, we confirm with a moisture meter and give you a report your plumber can use to make the repair.

Problem

Mold keeps coming back after cleaning

If mold returns after cleaning, the moisture source was never fixed. Cleaning the visible mold without addressing the water is a temporary fix that wastes money and leaves the underlying problem in place.

Our Fix

We find the moisture source first. Thermal imaging shows where water is still entering or accumulating, and moisture readings confirm the extent. Once the source is identified, we recommend a remediation protocol that addresses both the mold and the water.

Why Fort Worth homeowners book a thermal scan

Why Fort Worth homeowners book a thermal scan

An infrared scan answers the question every homeowner asks after a leak: where is the water actually coming from? Here is what you get when you book with us.

  • Find leaks without demolition

    We locate hidden moisture behind tile, under hardwood, and inside wall cavities without tearing anything out. A typical scan covers 1,500 to 2,500 square feet in 60 to 90 minutes. You get a map of every wet zone and a clear next step, not a guess about which wall to open.

  • Catch mold before it spreads

    Mold needs 24 to 48 hours of moisture to start growing. Thermal imaging catches that moisture while the drywall is still salvageable. We have walked into Fort Worth homes where a single slow supply-line drip had soaked 40 square feet of wall cavity, and the homeowner had no idea until the camera showed the cold spot.

  • Document everything for insurance

    Every scan includes timestamped thermal images, moisture readings, and a written summary. Adjusters accept this documentation because it shows the exact extent of the water intrusion. If you are filing a claim after a storm or a slab leak, this report does the heavy lifting for you.

  • Stop paying for the wrong repair

    Too many homeowners pay for a new roof when the real leak is a failed shower pan, or replace flooring when the source is a cracked slab line. An affordable infrared inspection Fort Worth TX costs a fraction of a wrong repair. We tell you where the water is coming from so you fix the right thing once.

Licensed, certified, and local

Licensed & Certified

  • IICRC Certified Firm — issued by Institute of Inspection, Cleaning and Restoration Certification
  • ACAC Certified Microbial Consultant — issued by American Council for Accredited Certification
  • CIEC Certified Indoor Environmental Consultant — issued by American Council for Accredited Certification
  • TDLR Licensed Mold Assessment Company — issued by Texas Department of Licensing and Regulation
  • ANSI/IICRC S520 Standard Compliance — issued by Institute of Inspection, Cleaning and Restoration Certification

Verified Reviews

Google ★★★★★4.9

Fast, thorough, and honest. They found a slab leak that two plumbers missed and gave us a report the same day. The thermal images made it obvious where the water was coming from. Highly recommend for any Fort Worth homeowner with a mystery leak.

Yelp ★★★★★4.8

We used them for a post-storm moisture check on our attic. They showed up on time, scanned the whole space, and documented everything with photos and moisture readings. Our insurance adjuster accepted the report without question. Professional from start to finish.

BBB ★★★★★4.9

I manage rental properties and have used them multiple times. They always show up when they say they will, and their reports are detailed enough that my remediation contractor can start work the same day. That reliability is worth a lot in this business.

Google ★★★★★5.0

Called them after noticing a musty smell in our bedroom. They scanned the whole house, found the moisture source in under an hour, and explained everything in plain language. No pressure to buy extra services. Just clear findings and a clear plan.

Frequently Asked Questions

Real answers to the questions we hear most often from local homeowners and property managers.

How much does Thermal Imaging Inspection cost in Fort Worth TX?
Most residential thermal imaging inspections in Fort Worth run $250 to $450 in 2026, depending on square footage and how many areas we scan. A single-room scan for a known leak starts around $150. If you add air sampling or an ERMI test, expect $150 to $300 more per sample. We quote the full price before we arrive, so there is no surprise on the invoice.
What does an infrared inspection include in Fort Worth?
An infrared inspection in Fort Worth includes a full thermal scan of accessible walls, ceilings, and floors, moisture confirmation with a Protimeter meter, a hygrometer reading for indoor humidity, and a written report with thermal images and moisture percentages. We also check the attic, crawl space, and HVAC closets. The scan takes 60 to 90 minutes for a typical 2,000-square-foot home.
Can thermal imaging detect mold in Fort Worth TX?
Thermal imaging does not see mold itself, but it sees the moisture mold needs to grow. When the camera flags a cold spot and the moisture meter confirms elevated readings, we know that area is a candidate for mold growth. From there, we can take air samples with an Air-O-Cell cassette or a tape lift sample to confirm whether mold spores are present. That two-step approach is far more reliable than a camera alone.
Does Thermal Imaging Inspection find hidden moisture in Fort Worth?
Yes. Hidden moisture is exactly what thermal imaging is built to find. We routinely locate slow slab leaks, roof leaks that have not yet stained the ceiling, and shower pan failures that have soaked the subfloor without showing a visible sign. In Fort Worth, slab leaks and roof flashing failures are the two most common hidden moisture sources we find. Both show up clearly on a thermal scan.

Related Services

Mold Inspection

A full mold inspection pairs with thermal imaging to confirm whether the moisture we find has already turned into a mold problem. We inspect the attic, crawl space, HVAC system, and every room, then document findings in a written report you can use for remediation or real estate.

View Mold Inspection

Mold Testing

When thermal imaging flags a suspect area, mold testing confirms it. We use Zefon Air-O-Cell spore trap cassettes, tape lift sampling, and swab sampling, with lab analysis through EMSL Analytical or LabCorp. Results come back in two to three business days with species identification.

View Mold Testing

Air Quality Testing

Thermal imaging shows where moisture is; air quality testing shows what is airborne. We use a particle counter and air sampling pump to measure spore counts room by room. This is the fastest way to tell whether a hidden leak has already affected the air your family breathes.

View Air Quality Testing

Moisture Mapping and Detection

Moisture mapping takes the thermal scan one step further. We mark the exact boundaries of every wet zone on a floor plan, then take readings at multiple depths with a Protimeter meter. This gives remediation crews a precise scope of work and helps your insurance adjuster size the claim.

View Moisture Mapping and Detection

Mold Remediation Protocol

If thermal imaging confirms a mold problem, we write a remediation protocol that specifies containment, HEPA filtration, antimicrobial coatings, and clearance criteria. The protocol follows ANSI/IICRC S520 and gives your remediation contractor a clear, code-correct scope to work from.

View Mold Remediation Protocol

Post-Remediation Clearance Testing

After remediation, we return to verify the work. We run air sampling and surface sampling, check moisture levels with a hygrometer, and confirm that the area meets clearance criteria. You get a written clearance report that documents the job is done and the space is safe to reoccupy.

View Post-Remediation Clearance Testing

Book your Thermal Imaging Inspection Fort Worth TX today

If you have a musty smell, a new water stain, or a water bill that jumped, do not wait. We are licensed, insured, and we back every scan with a written report. Call us now and we will schedule your thermal imaging inspection, often the same day.

Call Now Book Inspection

Contact Fort Worth Mold Testing

Call (866) 896-8166 or email info@fortworthmoldtesting.com and we will get you on the schedule. We answer calls Monday through Friday from 8am to 6pm and run emergency response for water damage and post-storm inspections. Most standard inspections are booked within a day or two.

Or call us right now at +18668968166 — we answer.

Fort Worth Mold Testing


  • Phone

    +18668968166
  • Address

    Fort Worth, Texas

  • Hours

    Mon–Fri: 7AM – 7PM
    Sat: 8AM – 4PM
    Sun: Emergency Only
    24/7 Emergency Available

Call +18668968166 Get Quote
Call Quote